Ciao a tutti, per me la situazione è questa, c'è un accordo tra i produttori di batterie di non fornire i codici BEM ai rivenditori e quindi a potenziali acquirenti privati, quasi tutte i produttori poi forniscono (vendono) dei palmari che si collegano alla OBD che hanno in memoria i codici di tutte le batterie (di tutte le marche). Altri danno la possibilità di registrazioni a pagamento sul loro sito dove forniscono tutti i codici. Questo per scoraggiare l'installazione di batterie AGM da parte di privati e delegarlo alle officine (non gratis ovviamente).
Il codice BEM è composto da un primo valore di 10/11 caratteri che identifica il tipo di batteria ed è sempre uguale per tutte le batterie dello stesso modello, il secondo di 10 caratteri indica il N di matricola e poi va inserita anche la marca.
Secondo me il problema si risolve recuperando i codici da foto di batterie esistenti (tipo si ebay) e inserendo quelli, ovviamente si deve installare una batteria con caratteristiche equivalenti o leggermente superiori e dello stesso tipo (es. AGM), almeno a logica dovrebbe funzionare in quanto la centralina con il cambio del N di matricola sà che la batteria è stata sostituita (per mè è meglio recuperare N di matricola reali e non inventarli).

Per chi non ha il modulo 61 per entrare nel "battery regulation" ci sono altre due vie dal Mod. 19 CAN-Gateway che allego sotto : (fonte Ross-Tech)
C'è anche un video si Youtube.

61-Battery Regulation using CAN
This procedure applies to battery replacement in vehicles using a separate battery management control module.
Address 61: Battery Regul. Labels: 4F0-910-181.lbl
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A
Component: ENERGIEMANAGER H12 0490

Subsystem 1 - Part No: 000 915 105 C
Component: von VA0 2502160103
Coding: 303030393135313035432056413032353032313630313033
Shop #: WSC 54332 321 22222
Coding
[Select]
[61 - Battery Regulation]
[Coding - 07]
Use the pull down menu to select the battery (slave) listed as #1.
[Battery Coding]
• Enter the new Battery Part Number (10 or 11 digits).
• Enter the new Battery Serial Number (10 digits).
• Select the new Battery Vendor.
[OK]
[Do it!]
[Close Controller, Go Back - 06]
Your new Battery should now be coded and the Battery Control Module should be aware of the new Battery.
________________________________________
19-CAN Gateway using CAN
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.
Address 19: CAN Gateway (J533) Labels: 8T0-907-468.clb
Part No SW: 8T0 907 468 Q HW: 8T0 907 468 L
Component: GW-BEM 5CAN-M H10 0095

Subsystem 1 - Part No SW: 8K0 915 181 B HW: 8K0 915 181 B
Component: J367-BDM H04 0150
Long Adaptation
Installation of a new battery requires the use of the [Long Adaptation-0A] function under 19-CAN-Gateway control module. Follow the on-screen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.

[Select]
[19 - CAN-Gateway]
[Long Adaptation-0A]
Channel 004
[Read]
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ

N = Battery Part Number (11 Digits)
X = Battery Vendor (3 Digits)
Z = Battery Serial Number (10 Digits)
[Add to Log] Saving the original value to a log is strongly recommended.
Type the New Battery details into the New value field.
• Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.
[Test]
[Save]
Providing the value was accepted by the controller the new battery coding is complete.
[Done, Go Back]
[Close Controller, Go Back - 06]
Special Notes
• Measuring Block groups 008, 019 and 020 should show Battery information.
• Registered users encountering difficulty can contact us via email -or- join and post in our forum. Please include the Auto-Scan, Saved Adaptation Channel 004 Log prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.
tinyurl.com/pzgolq7
________________________________________
19-CAN Gateway using (UDS/ODX)
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.
Address 19: CAN Gateway (J533) Labels: None
Part No SW: 4G0 907 468 E HW: 4G0 907 468 A
Component: J533--Gateway H08 0213
ASAM Dataset: EV_GatewUDS 001025

Battery Monitoring Control Module:
Subsystem 1 - Part No SW: 8X0 915 181 HW: 8X0 915 181
Component: J367-BDM H07 0140
Adaptation
Installation of a new battery requires the use of the [Adaptation-10] function under 19-CAN-Gateway control module. Use the drop-down menus to enter the Part Number, Vendor, and Serial Number information located on the new battery .

[Select]
[19 - CAN-Gateway]
[Long Adaptation-0A]
• Battery adaptation - Size
o Select the battery Ah rating from the drop-down menu followed by [Do It!] and confirm [Yes]
• Battery adaptation - Manufacturer
o Select the battery manufacturer from the drop-down menu followed by [Do It!] and confirm [Yes]
• Battery adaptation - Serial number
o Type the serial number code from the replacement battery followed by [Do It!] and confirm [Yes]
Providing the value was accepted by the controller the new battery coding is complete.
[Done, Go Back]
[Close Controller, Go Back - 06]