Mastaro Fans Club Socio -84-
Cristian - A3 8P 2.0 TDI 140cv 16V - Bose Sound System - Nero brillante - Assetto eibach B8 + Sportline -50mm
Conviene fare un'autoscan selezionando il modello di macchina,quando ha finito salvare la scansione ( il file salvato lo si trova dentro alla cartella di installazione del Vag....nella cartella "Log" )dopo cancellare gli errori.
ok... senza sporcare altre discussioni,sapete linkarmi anche sul forum vecchio le modifiche via vag che si possono fare sull's3 8L? io ho fatto quella dei km/litro,ma avevo letto quella della chiusura specchietti,della spia delle cinture,della chiusura delle porte oltre una certa velocità ecc ecc
grazie
in questo caso è meglio che lascio perdere
ciao ividea x quanto riguarda gli errori memorizzati nella centralina motori è vero ke sono tre ma il problema è uno solo;devi sostituire la valvola di spegnimento sull'aspirazione,ti da l'errore anke sulla ventola 1 xchè le due cose sono alimentate dallo stesso canale e quindi di sicuro ti ha bruciato il fusibile da 10Amp ke dovrebbe essere il numero 9.
Ti consiglio di staccare lo spinotto della valvola di spegnimento e sostituire il fusibile da 10 amp
ebbene mi accodo anche io perché sto uscendo pazzo e non riesco a risolvere questi errori:
-------------------------------------------------------------------------------
Address 19: CAN Gateway
Part No SW: 1K0 907 530 B HW: 1K0 907 951
Component: Gateway H08 0090
Coding: 3D0F0B42070100
Shop #: WSC 06435
1 Fault Found:
01044 - Control Module Incorrectly Coded
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 1
Fault Frequency: 1
Reset counter: 139
Mileage: 130735 km
Time Indication: 0
Date: 2008.07.28
Time: 18:46:58
-------------------------------------------------------------------------------
Address 08: Auto HVAC
Part No SW: 8P0 820 043 M HW: 8P0 820 043 M
Component: KlimavollautomatH18 0300
2 Faults Found:
00819 - High Pressure Sensor (G65)
009 - Open or Short to Ground - Intermittent
Freeze Frame:
Fault Status: 00101001
Fault Priority: 3
Fault Frequency: 1
Reset counter: 250
Mileage: 73974 km
Time Indication: 0
Date: 2008.03.06
Time: 00:08:38
Freeze Frame:
Temperature: 9.0°C
Voltage: 12.40 V
RPM: 0 /min
Load: 0.0 %
Load: 9.0 %
01592 - Air Quality Sensor (G238)
010 - Open or Short to Plus - Intermittent
Freeze Frame:
Fault Status: 00101010
Fault Priority: 3
Fault Frequency: 1
Reset counter: 250
Mileage: 73974 km
Time Indication: 0
Date: 2008.03.06
Time: 00:08:39
Freeze Frame:
Temperature: -50.0°C
ecco la lista getaway
Tuesday,15,July,2008,18:22:32
VAG-COM Version: Release 607.3-UD
Gateway Installation List: 1K0 907 530 B
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: OK 0000
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: Malfunction 0010
25-Immobilizer -- Status: OK 0000
37-Navigation -- Status: Not registered 0011
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
47-Sound System -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
56-Radio -- Status: Malfunction 0010
7D-Aux. Heat -- Status: OK 0000
ora questo maledetto CAN-Getaway non codificato correttamente come diavolo si sistema? Ho installato il naviplus ed ho provveduto a codificare il canale 56, tutto funziona ma mi resta l'errore. Poi per gli altri errori sembra essere il compressore del clima (che funziona) o sbaglio? Qualche guru?
Per quanto riguarda l'errore sulle centraline 19-37-56 si tratta del navigatore codificato male
per quanto riguarda il clima devi sostituire in primis il filtro antipolline,per il problema della pressione alta puo essere una ricarica effettuata male(senza aver fatto prima il vuoto) oppure il sensore di pressione starato
Si questo l'ho capito, ma il punto è come codificare anche il canale 19? E' diverso dal 56 o37
Thanks!
Questo è l'estratto del longcoding preso da openodb.org, vedo che al byte 03 bit 3 c'è il riferimento al navigatore, ma come si codifica, sarò scemo io ma non ho capito! Io uso un cavo clone con 6.07. Qual'è la procedura corretta ?
CAN-Gateway}
Control Module Coding
Select 19 (CAN-Gateway)
Long Coding -> Function 07
Byte 00 Bit 0 Engine (Address 01)
Byte 00 Bit 1 Auto. Transmission (Address 02)
Byte 00 Bit 2 Brake Electronics (Address 03)
Byte 00 Bit 3 Steering Angle Sensor (G85)
Byte 00 Bit 4 Airbag (Address 15)
Byte 00 Bit 5 Steering Aid (Address 44)
Byte 00 Bit 6 Xenon Range (Address 55)
Byte 00 Bit 7 All Wheel Drive (Address 22)
Byte 01 Bit 0 Central Electronics (Address 09)
Byte 01 Bit 1 Central Convenience (Address 46)
Byte 01 Bit 2 Door Electronics (Driver - Address 42)
Byte 01 Bit 3 Door Electronics (Passenger - Address 52)
Byte 01 Bit 4 Door Electronics (Rear Left - Address 62)
Byte 01 Bit 5 Door Electronics (Rear Right - Address 72)
Byte 01 Bit 6 Seat Memory Driver (Address 36)
Byte 01 Bit 7 Tire Pressure Monitoring (Address 65)
Byte 02 Bit 0 Steering Wheel Electronics (Address 16)
Byte 02 Bit 1 Auto HVAC (Address 08)
Byte 02 Bit 2 Parking Assistant (Address 76)
Byte 02 Bit 3 Auxiliary Heating (Address 7D)
Byte 02 Bit 4 Auxiliary Heating (Address 18)
Byte 02 Bit 5 Auto Roof (Address 26)
Byte 02 Bit 6 Trailer (Address 69)
Byte 02 Bit 7 Seat Memory Passenger (Address 06)
Byte 03 Bit 0 Special Function (Address 3D)
Byte 03 Bit 1 Sound System (Address 47)
Byte 03 Bit 2 Telematics (Address 75)
Byte 03 Bit 3 Navigation (Address 37)
Byte 03 Bit 4 TV-Tuner (Address 57)
Byte 03 Bit 5 Digital Radio (Address 0F)
Byte 03 Bit 6 Radio (Adress 56)
Byte 03 Bit 7 Telephone (Address 77)
Byte 04 Bit 0 Instrument Cluster (Address 17)
Byte 04 Bit 1 Immobilizer (Address 25)
Byte 04 Bit 2 CAN-Gateway (Address 19)
Segnalibri